Edge 1500 X

from 369.00 €

Delivery time: 1 day(s)


Please choose first the "Version", the "Material" and the "Build" to see the price and more details on your choice . Then you'll be able to put your product into the basket.

Despite the low flying weight of only 1,000-1,100 grams, the Edge 1500 X cuts a fine figure even in the toughest conditions of over 60 km / h wind speed - even without ballast.

The Edge 1500 X is characterized by its very good draft and its good and direct control behavior.

In slow flight and landing approach, he shows up as absolutely uncritical and tame.

Due to its small pack size of approx. 90 cm, it fits into any trunk or holiday suitcase.


  • Glider: Narrow fuselage. Motorization may be possible after consultation.
  • Electro: Electric fuselage with sufficient space for all components. No ballast tube in the fuselage (of course, all other ballasting options remains).


  • Glass/Carbon: Glass with various carbon reinforcements
  • Full Carbon: Carbon fuselage and wings. Very solid. (front fuselage partly with glass for better signal reception)


  • Standard Kit: All standard parts incl. wiring harness
  • Full Build Kit (Glider): Standard kit + servo set, battery and magnetic switch
  • Full Build Kit (Electro): Standard kit + servo set, spinner, propeller, motor, if necessary, a gearbox, controller and motor-battery (instead of a small receiver battery)
  • Read To Fly: Full Build Kit + complete assembly of the aircraft by us within a few days!


  • Easy to build..........⭐⭐⭐⭐⭐
  • Easy to set up........⭐⭐⭐
  • Easy to fly..............⭐⭐⭐
  • Speed.................... ⭐⭐⭐⭐
  • Thermal................. ⭐⭐
  • Agility..................... ⭐⭐⭐⭐

Technical data:

  • Wingspan: 1.500 mm
  • Wing area: 21,4 dm²
  • Wing Aspect Ratio: 10,5
  • Airfoil thickness: 8 %
  • Center of gravity: 65 mm
  • Flight weight: 1050 gr
  • Wing loading: 48,8 gr/dm²
  • Airfoil: JH 7/8
  • Fuselage ballast: Ø15mm x 33mm (6x)
  • Ballasting steel joiner instead of carbon joiner: (not included in our delivery): 250 gr.


  • Elevator
  • Rudder
  • Ailerons
  • Flaps

Wings and tailplane:

  • High strength gel-coat glass/carbon wings in shell design
  • Clean, high quality processing
  • Various carbon inlays at high stressed points
  • Painted in the mould
  • Top side white
  • Bottom side green
  • All part joiner made from carbon ⭐
  • All part joiner pre-finished and ready for assembly ⭐
  • All tailplane joiner pre-finished and ready for assembly ⭐
  • Sealing lips on all rudders ⭐


  • High strength gelcoat glass/carbon fuselage
  • Clean, high quality processing
  • Multiple non-stop carbon inserts ⭐
  • Various carbon inlays at high stressed points ⭐
  • Painted in the mould
  • Green canopy

Accessories included:

  • Glass canopy with glued carbon fastening spring ⭐
  • Glass ballast tube ⭐
  • Glass servo covers Servo support plate (fuselage)
  • 4x servo frames (wings)
  • Carbon wing joiner
  • Glass control horns ⭐
  • High quality clevis made of spring steel ⭐
  • Small parts set Standard protective bags with velcro closure for wings, tail unit and fuselage ⭐
  • Pre-assembled and encapsulated wiring harness ⭐

Further recommended accessories:

  • Fitting servo set (available here in the shop) ⭐
  • LiPo 7.4V 800 mAh (available here in the shop) ⭐
  • Magnetic switch (available here in the shop) ⭐
  • Foils sticker sheet incl. transfer foil and felt squeegee (available here in the shop) ⭐

Servo recommendation:

  • Tail: 2x KST X12
  • Aileron: 2x KST X08
  • Flaps: 2x KST X08
  • Note our low-priced servo sets in the accessories area! ⭐

Rudder setup:

  • Elevator: 8 mm up/down
  • Rudder: 15 mm left/right
  • Aileron: 7 mm up, 4 mm down
  • Flaps: 50 degrees
  • Snap-Flap: 2 mm landing flap, aileron fitting
  • Crow: landing flap 70 degrees down, aileron 16 degrees up, elevator 3 mm down
  • Speed: flaps 1-2 mm high, ailerons matching

(All mm data measured at the position of the largest deflection of the rudder)

Information about motorization:

  • Motor mount 35 mm
  • Spinner: 36 mm
  • Motor: A20-12XL
  • Controller: Hacker X-30-pro
  • Battery: Hacker LiPo 3S - 2400 mAh
  • Propeller: 11 x 6 ACC


Questions? info@composite-rc-gliders.com